次の Verilog コードがあります。
//////////////////////////////////////////////////////////////////////////////
//
// Xilinx, Inc. 2010 www.xilinx.com
//
// XAPP xxx - 1:5 Differential Data De-serializer
//
//////////////////////////////////////////////////////////////////////////////
//
// File name : serdes_1_to_5_diff_data.v
//
// Description : This module instantiates IODELAY2 and ISERDES2 primitives
// to receive TMDS differential data in 1:5 format
//
// Note:
//
// Author : Bob Feng
//////////////////////////////////////////////////////////////////////////////
//
// Disclaimer:
//
// This disclaimer is not a license and does not grant any rights to the materials
// distributed herewith. Except as otherwise provided in a valid license issued to you
// by Xilinx, and to the maximum extent permitted by applicable law:
// (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND WITH ALL FAULTS,
// AND XILINX HEREBY DISCLAIMS ALL WARRANTIES AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY,
// INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, OR
// FITNESS FOR ANY PARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whether in contract
// or tort, including negligence, or under any other theory of liability) for any loss or damage
// of any kind or nature related to, arising under or in connection with these materials,
// including for any direct, or any indirect, special, incidental, or consequential loss
// or damage (including loss of data, profits, goodwill, or any type of loss or damage suffered
// as a result of any action brought by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the possibility of the same.
//
// Critical Applications:
//
// Xilinx products are not designed or intended to be fail-safe, or for use in any application
// requiring fail-safe performance, such as life-support or safety devices or systems,
// Class III medical devices, nuclear facilities, applications related to the deployment of airbags,
// or any other applications that could lead to death, personal injury, or severe property or
// environmental damage (individually and collectively, "Critical Applications"). Customer assumes
// the sole risk and liability of any use of Xilinx products in Critical Applications, subject only
// to applicable laws and regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS PART OF THIS FILE AT ALL TIMES.
//
//////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
module serdes_1_to_5_diff_data # (
parameter DIFF_TERM = "TRUE",
parameter SIM_TAP_DELAY = 49,
parameter BITSLIP_ENABLE = "FALSE"
)(
input wire use_phase_detector, // '1' enables the phase detector logic
input wire datain_p, // Input from LVDS receiver pin
input wire datain_n, // Input from LVDS receiver pin
input wire rxioclk, // IO Clock network
input wire rxserdesstrobe, // Parallel data capture strobe
input wire reset, // Reset line
input wire gclk, // Global clock
input wire bitslip, // Bitslip control line
output wire [4:0] data_out // Output data
);
wire ddly_m;
wire ddly_s;
wire busys;
wire rx_data_in;
wire cascade;
wire pd_edge;
reg [8:0] counter;
reg [3:0] state;
reg cal_data_sint;
wire busy_data;
reg busy_data_d;
wire cal_data_slave;
reg enable;
reg cal_data_master;
reg rst_data;
reg inc_data_int; //THIS LINE (81) IS CAUSING THE ERROR
wire inc_data;
reg ce_data;
reg valid_data_d;
reg incdec_data_d;
reg [4:0] pdcounter;
wire valid_data;
wire incdec_data;
reg flag;
reg mux;
reg ce_data_inta ;
wire [1:0] incdec_data_or;
wire incdec_data_im;
wire [1:0] valid_data_or;
wire valid_data_im;
wire [1:0] busy_data_or;
wire all_ce;
wire [1:0] debug_in = 2'b00;
assign busy_data = busys ;
assign cal_data_slave = cal_data_sint ;
/////////////////////////////////////////////////
//
// IDELAY Calibration FSM
//
/////////////////////////////////////////////////
always @ (posedge gclk or posedge reset)
begin
if (reset == 1'b1) begin
state <= 0 ;
cal_data_master <= 1'b0 ;
cal_data_sint <= 1'b0 ;
counter <= 9'h000 ;
enable <= 1'b0 ;
mux <= 1'h1 ;
end
else begin
counter <= counter + 9'h001 ;
if (counter[8] == 1'b1) begin
counter <= 9'h000 ;
end
if (counter[5] == 1'b1) begin
enable <= 1'b1 ;
end
if (state == 0 && enable == 1'b1) begin // Wait for IODELAY to be available
cal_data_master <= 1'b0 ;
cal_data_sint <= 1'b0 ;
rst_data <= 1'b0 ;
if (busy_data_d == 1'b0) begin
state <= 1 ;
end
end
else if (state == 1) begin // Issue calibrate command to both master and slave, needed for simulation, not for the silicon
cal_data_master <= 1'b1 ;
cal_data_sint <= 1'b1 ;
if (busy_data_d == 1'b1) begin // and wait for command to be accepted
state <= 2 ;
end
end
else if (state == 2) begin // Now RST master and slave IODELAYs needed for simulation, not for the silicon
cal_data_master <= 1'b0 ;
cal_data_sint <= 1'b0 ;
if (busy_data_d == 1'b0) begin
rst_data <= 1'b1 ;
state <= 3 ;
end
end
else if (state == 3) begin // Wait for IODELAY to be available
rst_data <= 1'b0 ;
if (busy_data_d == 1'b0) begin
state <= 4 ;
end
end
else if (state == 4) begin // Wait for occasional enable
if (counter[8] == 1'b1) begin
state <= 5 ;
end
end
else if (state == 5) begin // Calibrate slave only
if (busy_data_d == 1'b0) begin
cal_data_sint <= 1'b1 ;
state <= 6 ;
end
end
else if (state == 6) begin // Wait for command to be accepted
cal_data_sint <= 1'b0 ;
if (busy_data_d == 1'b1) begin
state <= 7 ;
end
end
else if (state == 7) begin // Wait for all IODELAYs to be available, ie CAL command finished
cal_data_sint <= 1'b0 ;
if (busy_data_d == 1'b0) begin
state <= 4 ;
end
end
end
end
always @ (posedge gclk or posedge reset) // Per-bit phase detection state machine
begin
if (reset == 1'b1) begin
pdcounter <= 5'b1000 ;
ce_data_inta <= 1'b0 ;
flag <= 1'b0 ; // flag is there to only allow one inc or dec per cal (test)
end
else begin
busy_data_d <= busy_data_or[1] ;
if (use_phase_detector == 1'b1) begin // decide whther pd is used
incdec_data_d <= incdec_data_or[1] ;
valid_data_d <= valid_data_or[1] ;
if (ce_data_inta == 1'b1) begin
ce_data = mux ;
end
else begin
ce_data = 64'h0000000000000000 ;
end
if (state == 7) begin
flag <= 1'b0 ;
end
else if (state != 4 || busy_data_d == 1'b1) begin // Reset filter if state machine issues a cal command or unit is busy
pdcounter <= 5'b10000 ;
ce_data_inta <= 1'b0 ;
end
else if (pdcounter == 5'b11111 && flag == 1'b0) begin // Filter has reached positive max - increment the tap count
ce_data_inta <= 1'b1 ;
inc_data_int <= 1'b1 ;
pdcounter <= 5'b10000 ;
flag <= 1'b1 ;
end
else if (pdcounter == 5'b00000 && flag == 1'b0) begin // Filter has reached negative max - decrement the tap count
ce_data_inta <= 1'b1 ;
inc_data_int <= 1'b0 ;
pdcounter <= 5'b10000 ;
flag <= 1'b1 ;
end
else if (valid_data_d == 1'b1) begin // increment filter
ce_data_inta <= 1'b0 ;
if (incdec_data_d == 1'b1 && pdcounter != 5'b11111) begin
pdcounter <= pdcounter + 5'b00001 ;
end
else if (incdec_data_d == 1'b0 && pdcounter != 5'b00000) begin // decrement filter
pdcounter <= pdcounter + 5'b11111 ;
end
end
else begin
ce_data_inta <= 1'b0 ;
end
end
else begin
ce_data = all_ce ;
inc_data_int = debug_in[1] ;
end
end
end
assign inc_data = inc_data_int ;
assign incdec_data_or[0] = 1'b0 ; // Input Mux - Initialise generate loop OR gates
assign valid_data_or[0] = 1'b0 ;
assign busy_data_or[0] = 1'b0 ;
assign incdec_data_im = incdec_data & mux; // Input muxes
assign incdec_data_or[1] = incdec_data_im | incdec_data_or; // AND gates to allow just one signal through at a tome
assign valid_data_im = valid_data & mux; // followed by an OR
assign valid_data_or[1] = valid_data_im | valid_data_or; // for the three inputs from each PD
assign busy_data_or[1] = busy_data | busy_data_or; // The busy signals just need an OR gate
assign all_ce = debug_in[0] ;
IBUFDS #(
.DIFF_TERM (DIFF_TERM))
data_in (
.I (datain_p),
.IB (datain_n),
.O (rx_data_in)
);
//
// Master IDELAY
//
IODELAY2 #(
.DATA_RATE ("SDR"),
.IDELAY_VALUE (0),
.IDELAY2_VALUE (0),
.IDELAY_MODE ("NORMAL" ),
.ODELAY_VALUE (0),
.IDELAY_TYPE ("DIFF_PHASE_DETECTOR"),
.COUNTER_WRAPAROUND ("STAY_AT_LIMIT"), //("WRAPAROUND"),
.DELAY_SRC ("IDATAIN"),
.SERDES_MODE ("MASTER"),
.SIM_TAPDELAY_VALUE (SIM_TAP_DELAY)
) iodelay_m (
.IDATAIN (rx_data_in), // data from IBUFDS
.TOUT (), // tri-state signal to IOB
.DOUT (), // output data to IOB
.T (1'b1), // tri-state control from OLOGIC/OSERDES2
.ODATAIN (1'b0), // data from OLOGIC/OSERDES2
.DATAOUT (ddly_m), // Output data 1 to ILOGIC/ISERDES2
.DATAOUT2 (), // Output data 2 to ILOGIC/ISERDES2
.IOCLK0 (rxioclk), // High speed clock for calibration
.IOCLK1 (1'b0), // High speed clock for calibration
.CLK (gclk), // Fabric clock (GCLK) for control signals
.CAL (cal_data_master), // Calibrate control signal
.INC (inc_data), // Increment counter
.CE (ce_data), // Clock Enable
.RST (rst_data), // Reset delay line
.BUSY () // output signal indicating sync circuit has finished / calibration has finished
);
//
// Slave IDELAY
//
IODELAY2 #(
.DATA_RATE ("SDR"),
.IDELAY_VALUE (0),
.IDELAY2_VALUE (0),
.IDELAY_MODE ("NORMAL" ),
.ODELAY_VALUE (0),
.IDELAY_TYPE ("DIFF_PHASE_DETECTOR"),
.COUNTER_WRAPAROUND ("WRAPAROUND"),
.DELAY_SRC ("IDATAIN"),
.SERDES_MODE ("SLAVE"),
.SIM_TAPDELAY_VALUE (SIM_TAP_DELAY)
) iodelay_s (
.IDATAIN (rx_data_in), // data from IBUFDS
.TOUT (), // tri-state signal to IOB
.DOUT (), // output data to IOB
.T (1'b1), // tri-state control from OLOGIC/OSERDES2
.ODATAIN (1'b0), // data from OLOGIC/OSERDES2
.DATAOUT (ddly_s), // Slave output data to ILOGIC/ISERDES2
.DATAOUT2 (), //
.IOCLK0 (rxioclk), // High speed IO clock for calibration
.IOCLK1 (1'b0),
.CLK (gclk), // Fabric clock (GCLK) for control signals
.CAL (cal_data_slave), // Calibrate control signal
.INC (inc_data), // Increment counter
.CE (ce_data), // Clock Enable
.RST (rst_data), // Reset delay line
.BUSY (busys) // output signal indicating sync circuit has finished / calibration has finished
);
//
// Master ISERDES
//
ISERDES2 #(
.DATA_WIDTH (5),
.DATA_RATE ("SDR"),
.BITSLIP_ENABLE (BITSLIP_ENABLE),
.SERDES_MODE ("MASTER"),
.INTERFACE_TYPE ("RETIMED"))
iserdes_m (
.D (ddly_m),
.CE0 (1'b1),
.CLK0 (rxioclk),
.CLK1 (1'b0),
.IOCE (rxserdesstrobe),
.RST (reset),
.CLKDIV (gclk),
.SHIFTIN (pd_edge),
.BITSLIP (bitslip),
.FABRICOUT (),
.Q4 (data_out[4]),
.Q3 (data_out[3]),
.Q2 (data_out[2]),
.Q1 (data_out[1]),
.DFB (),
.CFB0 (),
.CFB1 (),
.VALID (valid_data),
.INCDEC (incdec_data),
.SHIFTOUT (cascade));
//
// Slave ISERDES
//
ISERDES2 #(
.DATA_WIDTH (5),
.DATA_RATE ("SDR"),
.BITSLIP_ENABLE (BITSLIP_ENABLE),
.SERDES_MODE ("SLAVE"),
.INTERFACE_TYPE ("RETIMED")
) iserdes_s (
.D (ddly_s),
.CE0 (1'b1),
.CLK0 (rxioclk),
.CLK1 (1'b0),
.IOCE (rxserdesstrobe),
.RST (reset),
.CLKDIV (gclk),
.SHIFTIN (cascade),
.BITSLIP (bitslip),
.FABRICOUT (),
.Q4 (data_out[0]),
.Q3 (),
.Q2 (),
.Q1 (),
.DFB (),
.CFB0 (),
.CFB1 (),
.VALID (),
.INCDEC (),
.SHIFTOUT (pd_edge));
reg [7:0] rxpdcntr = 8'h7f;
always @ (posedge gclk or posedge reset) begin
if (reset)
rxpdcntr <= 8'h7f;
else if (ce_data)
if (inc_data)
rxpdcntr <= rxpdcntr + 1'b1;
else
rxpdcntr <= rxpdcntr - 1'b1;
end
endmodule
Xilinx Platform Studio でこのデザインのネットリストを生成しようとすると、次のようなエラー メッセージが表示されます。
ERROR:HDLCompiler:1511 - "/home/eamorr/Desktop/Dropbox/UCD/digitalEye/Atlys_HDMI_PLB_demo/project/pcores/hdmi_in_v1_00_a/hdl/verilog/serdes_1_to_5_diff_data.v" Line 82: Mix of blocking and non-blocking assignments to variable <inc_data_int> is not a recommended coding practice.
ERROR:EDK:546 - Aborting XST flow execution!
ERROR:EDK:440 - platgen failed with errors!
make: *** [implementation/system_microblaze_0_wrapper.ngc] Error 2
私は完全に立ち往生していて、何をすべきかわかりません。