私は電動ローラーブラインドプロジェクトを持っています。私はこの指示に従っています: https://www.instructables.com/id/Motorized-WiFi-IKEA-Roller-Blind/ .
私は指示可能なコードを使用していますが、これらのコードのいずれかに問題があると思われます。
config.lua
-- file : config.lua
local module = {}
module.SSID = {}
module.SSID["ssid"] = "password"
-- example for local MQTT
--module.MQHOST = "ohab.local"
--module.MQPORT = 1883
--module.MQID = node.chipid()
--module.MQUSR = ""
--module.MQPW = ""
-- example for cloud MQTT
module.MQHOST = "192.***.*.*"
module.MQPORT = 1883
module.MQID = node.chipid()
module.MQUSR = "username"
module.MQPW = "password"
module.MQTLS = 1 -- 0 = unsecured, 1 = TLS/SSL
module.ENDPOINT = "/house/masterbedroom/rollerblind/"
module.ID = "0"
--module.SUB = "set"
module.SUB = {[module.ENDPOINT .. module.ID .. "/set"]=0,[module.ENDPOINT .. "all"]=0}
module.POST = module.ENDPOINT .. module.ID .. "/status"
return module
wifi_setup
-- file: setup.lua
local module = {}
local function wifi_wait_ip()
if wifi.sta.getip()== nil then
print("IP unavailable, Waiting...")
else
tmr.stop(1)
gpio.write(pin_led,1) --off
print("\n================== ==================")
print("ESP8266 mode is: " .. wifi.getmode())
print("MAC address is: " .. wifi.ap.getmac())
print("IP is "..wifi.sta.getip())
print("====================================")
mq.start()
end
end
local function wifi_start(list_aps)
if list_aps then
gpio.write(pin_led,0) --on
for key,value in pairs(list_aps) do
if config.SSID and config.SSID[key] then
wifi.setmode(wifi.STATION);
wifi.sta.config(key,config.SSID[key])
wifi.sta.connect()
print("Connecting to " .. key .. " ...")
--config.SSID = nil -- can save memory
tmr.alarm(1, 2500, 1, wifi_wait_ip)
end
end
else
print("Error getting AP list")
end
end
function module.start()
print("Configuring Wifi ...")
wifi.setmode(wifi.STATION);
wifi.sta.getap(wifi_start)
end
return module
悲しいことに、ステップ 4 を超えることができません。コードを ESP8266 にダウンロードしようとした後、次のエラーのみが表示されます。
パニック: Lua API の呼び出しで保護されていないエラーが発生しました (wifi_setup.lua:25: 'config' への引数 #1 が正しくありません (構成テーブルが見つかりません!))
インストラクターが変更するように言ったものだけを変更し、自分で障害を探してみましたが、何も見つかりません... Luaを使用するのは初めてなので、これは私にとってまったく新しいことです。
ここで誰かが助けてくれることを願っています。何日もこれにこだわっています...
問題のこの部分は解決されました。解決策についてはコメントを確認してください
悲しいことに、1 つの問題が解決すると、新しい問題が発生します...
チップは現在、wifi および mqtt サービスに正常に接続していますが、コマンド 'step_move(1000,FWD,2)' を入力してドライ ランを実行しようとすると、何も起こりません。モーターが回るはず...
また、ボタンを押すと、次のような新しいパニック エラーが発生します。
パニック: Lua API の呼び出しで保護されていないエラーが発生しました (button.lua:23: 上位値 '?' (nil 値) で演算を実行しようとしました)
ボタン.lua
--file button4.lua
do
-- use pin 1 as the input pulse width counter
local pin=5
local debounce = 150 --ms
local longpress = 2000 --ms
local pulse1, pulse2, du, now, trig = 1, 0, 0, tmr.now, gpio.trig
local prev_int_time, int_time, up_time = 0
local cal_steps = 100000
local cal_steps_dn = 0
local cal_steps_up = 0
local cal_state = 0 -- 0 = not calibration, 1 = calibrating down, 2 = calibrating up
state = 0 -- state: 0 = up, 1 = transition, 2 = down
gpio.mode(pin,gpio.INT)
local function pin4cb(level)
int_time = now() / 1000
if ((int_time - prev_int_time) > debounce) then
if (level == 0) then
up_time = int_time
else
if((int_time - up_time) > longpress) then
print("calibrating")
cal_state = 1
--cur_step = 100000
step_move(cal_steps,FWD,2)
else -- short press
print("short", cal_state)
if (cal_state == 2) then -- calibrated up (done)
print("calibration done")
state = 0 -- up
cur_step = 0
tot_steps = cal_steps - step_stepsleft
print("cal_steps: " .. cal_steps)
print("step_stepsleft: " .. step_stepsleft)
print("tot_steps: " .. tot_steps)
step_stop()
pins_disable()
cal_state = 0
if file.open("cfg_tot_steps.lua", "w+") then
file.write("tot_steps=" .. tot_steps .. '\n')
file.close()
end
elseif (cal_state == 1) then -- calibrated dn (switch direction)
print("calibration low point")
print(cal_steps - step_stepsleft)
step_stop()
step_move(cal_steps,REV,2)
cal_state = 2
elseif (cal_state == 0) then
if (state == 0 and step_stepsleft == 0) then -- i am up, go dowm
rollerblind.down()
-- state = 2
elseif (state == 1) then -- i am moving, do nothing
-- do nothing
elseif (state == 2 and step_stepsleft == 0) then -- i am down, go up
rollerblind.up()
-- state = 0
end
end
end
end
--print (level)
prev_int_time = int_time
end
end
gpio.trig(pin, "both", pin4cb)
end
stepper.lua のコードは次のとおりです。
-- stepper.lua
-- code from: http://www.esp8266.com/viewtopic.php?f=19&t=2326
-- simple stepper driver for controlling a stepper motor with a
-- l293d driver
-- nodemcu pins: 0 5 6 7
stepper_pins = {1,3,2,4} -- (A-)blue, (A+)pink, (B-)yellow, (B+)orange
--stepper_pins = {1,2,3,4}
-- half or full stepping
step_states4 = {
{1,0,0,1},
{1,1,0,0},
{0,1,1,0},
{0,0,1,1}
}
step_states8 = {
{1,0,0,0},
{1,1,0,0},
{0,1,0,0},
{0,1,1,0},
{0,0,1,0},
{0,0,1,1},
{0,0,0,1},
{1,0,0,1},
}
step_states = step_states4 -- choose stepping mode
step_numstates = 4 -- change to match number of rows in step_states
step_delay = 10 -- choose speed
step_state = 0 -- updated by step_take-function
step_direction = 1 -- choose step direction -1, 1
step_stepsleft = 0 -- number of steps to move, will de decremented
step_timerid = 4 -- which timer to use for the steps
status_timerid = 2 -- timer id for posing of status messages
-- setup pins
function pins_enable()
for i = 1, 4, 1 do
gpio.mode(stepper_pins[i],gpio.OUTPUT)
end
end
function pins_disable()
-- for i = 1, 4, 1 do -- no power, all pins
for i = 2, 4, 1 do -- no power, all pins except one (to keep it in place)
gpio.mode(stepper_pins[i],gpio.INPUT)
end
end
-- turn off all pins to let motor rest
function step_stopstate()
for i = 1, 4, 1 do
gpio.write(stepper_pins[i], 0)
end
end
-- make stepper take one step
function step_take()
-- jump to the next state in the direction, wrap
step_state = step_state + step_direction
cur_step = cur_step + step_direction * FWD
if step_state > step_numstates then
step_state = 1;
elseif step_state < 1 then
step_state = step_numstates
end
-- write the current state to the pins
pins_enable()
for i = 1, 4, 1 do
gpio.write(stepper_pins[i], step_states[step_state][i])
end
-- might take another step after step_delay
step_stepsleft = step_stepsleft-1
if step_stepsleft > 0 then
-- if cur_step > 0 and cur_step < tot_steps and step_stepsleft > 0 then
tmr.alarm(step_timerid, 10, 0, step_take )
--tmr.alarm(step_timerid, 10, 0, step_take )
else
step_stopstate()
step_stop()
pins_disable()
mq.post_status()
if file.open("cfg_cur_step.lua", "w+") then
file.write("cur_step=" .. cur_step .. '\n')
file.close()
end
end
end
-- public method to start moving number of 'int steps' in 'int direction'
function step_move(steps, direction, delay)
tmr.stop(step_timerid)
step_stepsleft = steps
step_direction = direction
step_delay = delay
step_take()
end
function step_go_to(step, delay)
if step >= cur_step then
steps = step - cur_step
step_move(steps, FWD, delay)
end
if step <= cur_step then
steps = cur_step - step
step_move(steps, REV, delay)
end
end
function percent_go_to(percent, delay)
if(percent >= 0 and percent <= 100) then
step_stop()
tmr.register(status_timerid, 1000, tmr.ALARM_AUTO, function () mq.post_status() end)
tmr.start(status_timerid)
step = percent * tot_steps / 100
step_go_to(step, delay)
end
end
-- public method to cancel moving
function step_stop()
tmr.stop(step_timerid)
tmr.stop(status_timerid)
step_stepsleft = 0
step_stopstate()
end